Skip to content
IGNA Online IGNA Online
  • Home
  • Blog
  • Start Here
  • Tools I Use
  • Contact
  • About
  • Privacy Policy

Tag: IOS-XE

Auto Draft
Networking

Securing the Management Plane on Cisco IOS-XE: SSH, VTY Hardening, Privilege Levels, and a Practical Checklist

10/27/2026 by IGNA Online 10 min read

A complete management plane hardening guide for Cisco IOS-XE: SSH v2 with modern ciphers, VTY access restrictions, Type 8/9 password hashing, privilege levels, parser views, disabling unnecessary services, NETCONF/RESTCONF security, and a practical 10-point verification checklist.

Read More →
Auto Draft
Networking

DMVPN Phase 2 on Cisco IOS-XE: Hub-and-Spoke to Spoke-to-Spoke VPN Configuration

08/19/2026 by IGNA Online 12 min read

A hands-on guide to DMVPN Phase 2 on Cisco IOS-XE, configure mGRE tunnels, NHRP, IPsec, and EIGRP for direct spoke-to-spoke VPN connectivity without static tunnel configuration between sites. Includes real CLI examples and troubleshooting guidance.

Read More →
Auto Draft
Networking

Cisco IOS-XE IP SLA and Object Tracking: Automated Dual-ISP Failover

07/02/2026 by IGNA Online 10 min read

Build a probe-verified dual-ISP failover system on Cisco IOS-XE using IP SLA and Object Tracking. When your primary ISP loses internet connectivity, even if the physical link stays up, automated failover kicks in within seconds without any manual intervention.

Read More →
Auto Draft
Networking

SNMP v3 on Cisco IOS-XE: Full Monitoring Setup with LibreNMS and Grafana

06/24/2026 by IGNA Online 10 min read

Learn how to configure SNMP v3 on Cisco IOS-XE devices with real CLI examples, then feed that data into LibreNMS and Grafana for production-grade network visibility.

Read More →
Auto Draft
Networking

Cisco Catalyst 9000 IOS-XE Software Upgrade Guide: Avoiding the Gotchas

05/31/2026 by IGNA Online 13 min read

A complete, command-by-command walkthrough for upgrading Cisco Catalyst 9300/9400/9500 switches: bundle mode vs. install mode, the install add/activate/commit workflow, ISSU eligibility, common failure scenarios including rommon recovery, post-upgrade verification, and rollback procedures, all with real IOS-XE output.

Read More →
Auto Draft
Networking

IPv6 Deployment on Cisco IOS-XE: A Practical Engineer’s Guide

05/04/2026 by IGNA Online 12 min read

Most enterprise networks still run dual-stack at best in 2026. This guide covers full IPv6 deployment on Cisco IOS-XE: addressing, OSPFv3, DHCPv6, ACLs, BGP, and the verification commands that actually tell you what’s broken, with real CLI output and production gotchas.

Read More →
OSPF Troubleshooting on Cisco IOS-XE: Adjacency Failures, Flapping, and Fixes
Networking

OSPF Troubleshooting on Cisco IOS-XE: Adjacency Failures, Flapping, and Fixes

04/26/2026 by IGNA Online 11 min read

A practical guide to diagnosing and fixing the most common OSPF adjacency failures on Cisco IOS-XE, MTU mismatches, timer conflicts, authentication errors, duplicate Router IDs, and flapping neighbors, with real show command output and CLI fixes.

Read More →
Cisco EEM Scripts: Automate IOS-XE with Embedded Event Manager
Networking

Cisco EEM Scripts: Automate IOS-XE with Embedded Event Manager

04/20/2026 by IGNA Online 11 min read

Cisco’s Embedded Event Manager (EEM) is one of the most underutilized features in IOS-XE. This guide covers six practical EEM applets, from BGP peer monitoring and interface flap detection to nightly config backups and CPU spike capture, with real CLI syntax and Cat9K-specific tips.

Read More →
Auto Draft
Networking

QoS on Cisco IOS/IOS-XE: A Practical Guide to Prioritizing Voice and Video Traffic

04/07/2026 by IGNA Online 11 min read

QoS misconfigurations are the number-one cause of jittery voice calls and stuttering video in enterprise networks. This guide walks through a production-ready MQC QoS policy for Cisco IOS and IOS-XE, covering DSCP markings, LLQ, CBWFQ, NBAR2 classification, and the exact show commands you need to verify it’s working.

Read More →
Auto Draft
Networking

Network Automation with Python: A Practical Guide to Netmiko, NAPALM, and Nornir

04/04/2026 by IGNA Online 12 min read

Stop logging into devices one by one. This hands-on guide covers Netmiko, NAPALM, and Nornir, the Python libraries that let network engineers automate Cisco IOS/IOS-XE tasks, parse show command output, push config changes, and run parallel jobs across hundreds of devices. Real code, real CLI examples, production-ready patterns.

Read More →
Cisco IOS vs IOS-XE vs IOS-XR: What's the Difference?
Networking

Cisco IOS vs IOS-XE vs IOS-XR: What’s the Difference?

02/28/2026 by IGNA Online 13 min read

A deep dive into Cisco’s three operating systems, IOS, IOS-XE, and IOS-XR, their architectures, platforms, CLI differences, and when you’ll encounter each.

Read More →

IGNA Online

Cisco networking and self-hosted homelab guides from a working network engineer. Where code meets the campsite.

Explore

  • Blog
  • Tools I Use
  • About
  • Contact
  • Start Here

Categories

  • Networking
  • Homelab & Self-Hosting
  • PC Hardware

Stay Connected

Get new posts delivered to your inbox.

RSS Feed

© 2025–2026 IGNA Online. All rights reserved.

Privacy Policy Back to Top